|
SCHOTT North America
|
SCHOTT PYRAN® Platinum L
Fire- and Safety-Rated Glass-Ceramic
PRODUCT INFORMATION
Description
PYRAN® Platinum L is a fire-protection rated and impact- safety rated glazing material with a thickness of approximately 3/8" (9 mm), a laminated glass-ceramic with a transparent appearance. It is intended for use in safety-rated locations such as door lites, transoms or sidelites, and windows with fire-rating requirements up to 90 minutes (doors: up to 3 hours).
|
 |
|
|
|
|
|
|
|
|
|
- Fire-rated up to 90 minutes (180 minutes in doors) with required hose stream test
- Laminated specially floated glass-ceramic
- Transparent and wireless
- Withstands thermal shock
- Suited for use with standard fire-rated frames with the same rating
- Conforms to positive pressure test standards
- Environmentally-frinedly glass-ceramic; produced without the use of toxins
- Can be used to construct insulated glazing units
|
- Thickness: 3/8" (9 mm)
- Weight: 4.0 lbs/ft²
- True color rendition
- Surface finish: mirror-like
- Maximum sheet sizes: Approximately 43" x 77"
- Impact rating: ANSI Z97.1 and CPSC 16CFR1201 (Cat. I and II)
- STC rating: approximately 36dB
|
Rating |
Location |
Max. exposed area of glazing (in²) |
Max. width of exposed glazing (in) |
Max. height of exposed glazing (in) |
Min. depth of grrove (in) |
| Up to 90 min |
Doors Non-Temp Rise |
2,736 (19 ft²) |
36 |
75 |
5/8 |
| Up to 180 min |
Doors Temp Rise and Non-Temp Rise |
100 (0.69 ft²) |
12 |
33 |
1/2 |
| Up to 90 min |
Other than Doors |
3,143 (21.8 ft²) |
75 |
76 |
5/8 |
|
Classified and labeled by Underwriters Laboratories, Inc. for the United
States and Canada with File-No. R22036. All fire tests performed in
accordance with UL 9, UL 10C, UBC 7-2 (1997), UBC 7-4 (1997), NFPA
257, NFPA 80, ASTM E2010-01, ASTM E2074-00, and ULC CAN4-S106.p>
Note: This product is not considered a barrier to radiant heat and has not met the ASTM E-119 or UL 263 test standards.
All listing information is subject to change. The current listing can be accessed in the UL directory under
file #R22036 or upon request from SCHOTT.
For special component requirements, contact SCHOTT North America, Inc., 5530 Shepherdsville Road, Louisville, KY 40228 or phone (502) 657-4417.
|
After cutting, each lite of PYRAN® Platinum L fire- and safety-rated glass-ceramic shall
be permanently labeled according to code requirements with product
and manufacturer’s name, mark from the authorized testing agency, fire
rating, etc.
|
PYRAN® Platinum L fire- and safety-rated glass-ceramic should be handled with care during transportation, storage, inspection, and installation. It should be
stored in dry conditions only and needs to be stacked upright or at a
slight angle. In addition, the panels must be separated by an appropriate
material, such as soft pads made of cork and the bottom edge must be
supported along its entire length.
|
PYRAN® Platinum L shall only be installed into fire-rated frame and window
assemblies carrying the same rating. Each PYRAN® Platinum L panel should be inspected carefully before installation, and any pieces with visible edge or surface damage should be sorted out. All glazing components and the stop height must be chosen according to the PYRAN® Platinum L UL classification. The panel must be placed on calcium silicate or hardwood setting blocks and glazed using PYRAN® Platinum L classified glazing tape, such as closed cell PVC, Fiberfrax tape or Pemko FG3000S90. The installation of the framed unit must comply with the frame supplier's instructions.
PYRAN® Platinum L is a specially developed glass-ceramic, that fulfills the fire protection rating requirements. The production process may create certain optical imperfections, such as bubbles or knots. Since these do not generally impair the transparency or the technical performance of the glass-ceramic, they do not represent cause for rejection or replacement.
|
To maintain the aesthetics, it is important to keep the panel clean. A soft,
clean, non-abrasive cloth and a mild soap, detergent, or non-abrasive
window cleaning solution is suitable for cleaning. After cleaning, rinse
immediately with clean water and remove any excess water from the
panel surface. Also, do not allow any metal or hard parts of the cleaning
equipment to come in contact with the panel surface.
|
|
Contact
Home Tech
SCHOTT North America, Inc.
5530 Shepherdsville Road
Louisville, KY 40228
USA
 | +1 (502) 657-4439 |
 | +1 (502) 966-4976 |
E-mail
More contacts
|
